Help Blog

Cub Cadet zero turn mowers are a popular choice for homeowners and businesses. Reliable and easy to use, Cub Cadet zero turns will also experience the occasional issue that can easily be troubleshooted at home with the appropriate tools. One of the most common at-home replacements is dealing with dull or damaged blades. If you find that your zero turn isn’t cutting grass as well as it used to, follow this step-by-step blade replacement guide.

Tools and Materials Needed

• Safety glasses
• Gloves
• Wrench
• Socket wrench
• New blade

Find your Cub Cadet Blade Replacement

Instructions

• Disconnect the spark plug wire from the spark plug.
• Use a wrench to loosen the blade bolt.
• Remove the blade bolt and the blade.
• Install the new blade and tighten the blade bolt.
• Reconnect the spark plug wire.

 

Use Cub Cadet Parts Lookup

Tips + Safety Precautions

• When replacing the blade, make sure that the blade is installed in the correct direction. The blade should be installed so that the cutting edge is facing down.
• Always wear safety glasses and gloves when working on any lawn mower.
• Disconnect the spark plug wire before working on the mower.
• Be careful not to overtighten the blade bolt. Overtightening the bolt can damage the blade or the mower deck.
• If you are not comfortable replacing the blade yourself, you can take your Cub Cadet zero turn mower to a qualified service technician.

The Cub Cadet XT1 LT46 Lawn Tractor is a powerful and reliable machine that is perfect for maintaining large lawns and gardens. With a 46-inch cutting deck, a powerful 22HP engine, and advanced hydrostatic transmission, it can tackle even the toughest mowing jobs with ease. However, like any other lawn tractor, it requires regular maintenance to ensure optimal performance. One of the essential maintenance tasks is changing the deck belt, which can wear out over time and need replacement. Follow this step-by-step guide on how to change the deck belt on your Cub Cadet XT1 LT46 Lawn Tractor.

Tools and Materials Needed:

• Cub Cadet XT1 LT46 Lawn Tractor
• Socket set
• Wrench set
• New deck belt

Step-by-Step Guide:

1. Turn off the engine and remove the key from the ignition to ensure safety.
2. Locate the deck lift lever and set it to the lowest position to gain better access to the deck.
3. Remove the deck by unscrewing the bolts and disconnecting the PTO cable.
4. Place the deck on a flat surface, such as a workbench or garage floor, and identify the deck belt.
5. Release the tension on the deck belt by pulling the idler pulley arm back and sliding the belt off the pulley.
6. Take note of the routing of the old deck belt, so you can easily install the new one later.
7. Remove the old deck belt by sliding it off the pulleys and removing it from the deck.
8. Install the new deck belt by following the routing that you noted earlier, starting at the engine pulley and working your way around the deck.
9. Ensure the deck belt is properly seated on all the pulleys, including the idler pulley.
10. Reconnect the PTO cable and reinstall the deck by aligning it with the brackets and securing the bolts.
11. Test the new deck belt by engaging the blades and checking for proper operation.
12. Raise the deck lift lever back to its original position and test the mower on a flat surface to ensure proper operation.
13.  

Changing the deck belt on your Cub Cadet XT1 LT46 Lawn Tractor is a straightforward process that can be done with basic tools and minimal mechanical experience. By following the steps outlined above, you can replace the deck belt on your lawn tractor and keep it running smoothly and efficiently. Don't forget to use our Parts Lookup Tool to find and order any replacement parts you may need for your Cub Cadet Lawn Tractor. With proper maintenance and care, your lawn tractor will continue to provide you with years of reliable service.

Over time, the deck belt on your Cub Cadet zero turn mower will experience typical wear and tear, and will eventually need replacement. If you don't replace your Cub Cadet belt in a timely manner, your machine might experience greater damage than necessary. Whenever you're changing or replacing the parts on your Cub Cadet equipment, make sure you refer to your owner's manual for specific instructions. To replace the deck belt on your Cub Cadet Z-Force 44 Riding Lawn Mower, follow this guide. 

 

 

Find and download the Cub Cadet Z-Force 44 Parts Manual that matches your equipment's model number here. To replace the deck belt on your Cub Cadet Z-Force 44, the corresponding Cub Cadet replacement part is 00050441. For models manufactured outside the years 2005 and 2006, double check your Parts Manual to ensure that you are using the correct replacement part. You can also use our Parts Lookup tool to find any and all Cub Cadet replacement parts that you might need. 

 

 

 

Cub Cadet Z-Force 44 Deck Belt Replacement Guide 

 

 

1. Prepare the mower for maintenance by placing your zero-turn on a level, flat surface. Before beginning any work, be sure the mower is off and the engine's had time to cool. Disconnect the spark plug ignition wire and make sure you engage the parking brake. This ensures your safety, and the safety of those near you. 

 

2. Remove the deck belt rod. Take the belt-keeper rod off and then remove the deck belt from the mower engine pulley. 

 

3. Lower the deck height. Adjust your deck lift lever so it is in the highest possible position, and slide in wooden blocks for more support. Now lower the deck of your mower onto the wooden blocks. 

 

4. Release the deck. You'll want to release the deck from the hangar brackets by removing the left and right J-Hooks. Now, carefully remove the wooden blocks from under the deck to lower it even further. Remove the click pin from the front deck hangar rod. 

 

5. Remove the mower deck. Begin by putting the deck height lever back in the highest possible position, and then turn the front wheels to the left. Slide the cutting deck out and to the right. If you find that you need to replace any other parts on your mower deck, now is the time to do so. 

 

6. Remove mower deck belt covers by using a ratchet. Also remove the nuts and bolts that secure the belt keeper to the deck idler pulley. Separate pulleys. 

 

7. Replacement time. Move the left idler pulley away from the machine, and lift off the old mower deck belt. Now you can loop the new deck belt around both pulleys. Reassemble nuts, bolts, pulleys, and covers. Follow the previous steps in reverse to complete step 7. 

 

8. Replace the zero-turn mower deck by sliding the deck back underneath the mower. Maneuver the new lawn mower deck belt around the engine pulley, and secure it in place with the rivet and rod. 

 

9. Replace hangar brackets. Put the click pin back into the deck's front hangar rod. Now replace the J-hooks back into their brackets on the left and right. 

 

Once you've replaced all necessary components, reconnect the spark plug ignition wire and raise or lower the deck so it's back to your standard mowing height–replacement completed. For assistance with Cub Cadet replacement parts, contact a CC Parts n' More specialist. 

Using your Cub Cadet RZT 50 to clean up the slope? Slopes are one of the major factors in loss of control and tip-over accidents. These types of accidents can result in severe injury and even death, so when using your RZT 50 on a slope, you need to exercise caution. Using our Dos and Don'ts of Slope Operation guide, learn about safest ways to use your RZT 50. 

 

As a general safety rule, you should always use the slope gauge (included in your Cub Cadet RZT 50 Manual) to measure the slop before operating your mower. If the slop is greater than 15 degrees, don't operate your Cub Cadet on the area, as it could cause serious injury. 

 

 

Dos: 

 

–Mow across slopes, not up and down. Be very careful when changing direction. 

–Keep an eye out for holes, ruts, bumps, rocks, and other hidden objects. Tall grass can hide obstacles, and uneven terrain can overturn your machine. 

–Operate at a slow speed. The speed you choose be slow enough that you don't need to stop while on the slope. You should also avoid starting or stopping on a slope. If your tires have difficulty maintaining traction, disengage the blades and proceed carefully and slowly straight down the slope. 

–Refer to the Cub Cadet recommendations for wheel weights or counterweights for improving stability. 

–When using grass catchers or other attachments, use extra care, as they can change the machine's stability. 

–All movement on the slope should be gradual and slow, never sudden. Don't make quick changes in speed or direction, as these rapid movements can cause the front of the machine to lift and rapidly flip over backwards, resulting in serious injury. 

 

 

Don'ts: 

 

–Don't turn on a slop unless it's absolutely necessary; then turn slowly uphill and use extra care while turning. 

–Don't mow near ditches, drop-offs, or embankments. These surfaces could cause the mower to suddenly turn over if a wheel goes over the edge of a cliff or ditch. 

–Don't attempt to stabilize your Cub Cadet by putting your foot on the ground. 

–Don't use the grass catcher attachment on steep slopes. 

–Don't mow wet grass; the reduced traction may cause sliding. 

–On slopes greater than 5 degrees, don't tow heavy pull-behind attachments, like a lawn roller or loaded dump cart. This extra weight tends to push the tractor downhill, and you may lose control of your equipment. 

 

Need belts or blades for your Cub Cadet RZT 50? Use our Parts Lookup tool. 

The last thing you need on a snowy, cold winter morning is to have your snow blower fail you. Here are a few recently asked questions to help troubleshoot some common snow blower/snow thrower issues. 

 

My snow blower won't discharge snow. What's wrong? 

If your blower/thrower isn't discharging, check the following: 

 

1. Auger drive belt: is it worn, loose, slipping, or off the pulley? Refer to your owner's manual for proper adjustment. 

 

2. Check the Auger control cable for proper adjustment. 

 

3. Are the auger or impeller pins sheared? If you need to install new shear pins, refer to your owner's manual. 

 

4. Inspect the discharge chute. Is it blocked? If so: 

    A) Never clean out the chute with your hands. Use the clean out tool. 

    B) Stop the engine and make sure all moving parts have stopped. Disconnect the spark plug wire, and keep the wire away from the plug to prevent accidental starting. 

    C) Use the clean out tool to clean the discharge chute. 

 

My snow blower has lost speed or traction. What should I check? 

 

1. Make sure the drive belt is secure in the pulleys, and that it's not worn or stretched. 

 

2. Inspect the drive disc for wear or contaminants. 

 

3. If your drive cable needs adjustment, refer to your owner's manual. 

 

4. Check tires for proper inflation pressure.

 

Need parts for your Husqvarna snow blower? Use our Parts Lookup tool, or contact a Cub Cadet Parts n' More specialist. 

As the winter season settles in, your snowblower needs to be ready to go in the case of an overnight snow that needs cleared before getting on with your day. Follow our guide for adjusting snowblower skid shoes in four easy steps below.

 

Skid shoes control the height of the scraper bar to the ground. The scraper bar protects the auger and auger housing from wear. When set at the correct height, the skid shoes prevents the scraper bar and augers from scraping against the ground. Skid shoes will wear down during during use, so the scraper bar needs to be checked regularly and skid shoes should be adjusted or replaced when necessary.

 

1. Place snowblower on a flat surface and adjust tire to the recommended PSI that is located on the side of the tire.

 

2. Place spacers under the scraper bar–NOT under the skid shoes. A piece of cardboard or washers works well for this purpose, as seen in the image below.  

 

 

   1/8 inch spacers are recommended for paved surfaces.

   1/2 inch spacers are recommended for gravel surfaces.

 

3. Loosen the bolts holding the skid shoes to the side of the blower housing.

 

 

 

3. Slide the skid shoes down and tighten bolts.

 

 

 

For delicate surfaces like pavers, bricks and decorative concrete consider using non-abrasive skid shoes.

 

For snowblower parts, use our Parts Lookup tool. 

Is your Cub Cadet snow thrower still stored away in the back of your garage? Maybe it's accumulated some dust out in the shed? With winter temperatures around the corner, snow is sure to follow. Follow our easy 5-step guide to prepare your snow blower for winter. 

 

1. Change the oil on your Cub Cadet snow thrower. You should also change the oil after the first five hours of winter-use, as well as at the end of the season. 
2. Check your spark plugs. Are they dirty? Clean the plugs. If you notice any rust or corrosion, you'll need to replace your spark plugs. Use our Parts Lookup tool to find replacement spark plugs!
3. Inspect all of your belts. Major wear and tear can cause damage to you or your equipment. If you need Cub Cadet replacement belts, we can help!
4. Re-fuel. Before adding new fuel, you'll need to drain your gas tank. When you add fresh fuel, you'll want to be sure your fuel includes a stablizer. This will prevent the fuel from going bad if you don't have to run your snow thrower for a couple of milder winter weeks. 
5. Before you run your Cub Cadet snow thrower, you'll want to sure all parts are in supreme working order. Lubricate the drive and chassis. Be sure to tighten nuts and bolts. 

When you've completed these five simple steps, start up your snow thrower and let it run for a few minutes to be sure no other issues arise. When performing maintenance on your Cub Cadet snow thrower, always exercise precaution, and use our Snow Blower Parts Diagrams when you need to look up a replacement part. 

Fall is the perfect season to take stock of your outdoor power equipment. Do you need replacement parts as the weather begins to change? What about that new tool you've been keeping your eye on? With fall in full force and winter approaching, it's a good time to clear those dead leaves from your yard. Read our guide and learn how to pick the right Troy-Bilt leaf blower.

 

First, think about the size of your yard. 

 

If your yard is small, a lightweight, electric blower will best suit your needs. 

 

For mid-size yards, think of a 2 or 4 cycle gas blower. These units are limited by power cords, and some come with vacuum bags for collecting the leaves. 

 

If you have a large yard, you may want to invest in a backpack or wheeled blower. The backpack blowers are more comfortable for longer periods of operation, while wheeled blowers are more powerful and ideal for clearing a lot of leaves from large yards. 

 

Next, consider the power and speed ratings of your ideal equipment. There are two ratings to pay attention to: MPH and cubic feet/minute (CFM). CFM measures the volume of air the blower can move in a minute, and the MPH measures the speed at which the machine blows. The higher the numbers, the higher blowing power your equipment has. If you need to remove heavy, wet leaves, you want to look for higher CFM and MPH ratings. 

 

Lastly, consider the ease of use of your Troy-Bilt leaf blower. Electric blowers require little maintenance and are very easy to use for small lawns. 4 cycle gas blowers take straight fuel, so require no mixing of oil and gas. 

 

All Troy-Bilt handheld gas blowers are jump start capable. Jump start power start technology eliminates pull starts. You simply plug the unit into your blower or other jump start capable equipment, squeeze the trigger, and get to work. 

 

If you have other questions about selecting the right Troy-Bilt leaf blower, or are in need of Troy-Bilt replacement parts, talk to one of our Cub Cadet Parts specialists. 

If your Cub Cadet mower's drive belt is worn-out, cracked, or torn, it's time to follow our replacement guide. 

 

Step One

Remove the ignition wire and spark plug. 

 

Step Two

Drain your fuel tank, keeping the fuel in a portable, government-approved container. 

 

Step Three 

Tip the mower onto its side so the air filter is up.

 

Step Four

On the side of the deck, remove the self-tapping screws.

 

Step Five

Safety first - wear your protective gloves. Secure the blade using your blade removal tool. 

 

Step Six

Remove the blade retaining bolt, followed by removing the blade itself. 

 

Step Seven

Remove the self-tapping secures that secure the mower drive belt cover and engine baffle to the deck. 

 

Step Eight

Remove the belt cover and baffle. 

 

Step Nine

Remove the drive belt from the drive pulley and blade adapter. 

 

Step Ten

Remove the blade adapter from the crankshaft. 

 

Step Eleven

Working from the back of the mower, exercise caution as you remove your Cub Cadet mower drive belt from the transmission pulley. 

 

Step Twelve

To access the engine pulley, push down on the deck baffle. Slide the drive belt off the pulley and out from under the deck. 

 

Step Thirteen

Replace your old belt with a new Cub Cadet drive belt. Work the belt between the deck and baffle by routing it around the transmission pulley, then the engine pulley.

 

Step Fourteen

Tighten the self-tapping screws that secure the deck baffle to the deck. 

 

Step Fifteen

Make sure you’re wearing gloves as you secure the blade using your universal blade removal tool. Replace the blade adapter and blade retaining bolt

 

Step Sixteen

Place the mower back on its wheels. 

 

Step Seventeen

Reattach your spark plug ignition wires, and refill the fuel tank. 

 

Practicing regular maintenance ensures the life of your Cub Cadet mower. When you’re in need of authentic, factory-direct Cub Cadet replacement parts, like Cub Cadet belts, Cub Cadet blades, Cub Cadet pulleys, and more, use our Parts Lookup tool or contact a specialist for more assistance.